, , , ,

Tilta Hydra Alien Car Mounting System


  • Modular car mount for DJI RS 2, RS 3, RS 3 Pro and RS 4 Pro
  • Four dovetail plates for high, low and side angles
  • One large and two small suction cups
  • Hydraulic damping arm and spring-loaded head
  • Power baseplate, 2x V-mount plates and D-Tap cables

€80,00 /Shoot Day

1 Day
2 Days
3 Days
4 Days
5 Days
1 Week
€80,00
€152,00
€216,00
€272,00
€320,00
€392,00
+ 10% discount for online bookings · Prices excl. VAT and insurance

To the description ↓

Tilta Hydra Alien Car Mounting System Specs
General
Compatible Gimbals DJI RS 2, RS 3, RS 3 Pro, RS 4 Pro
Battery Plates 2 x V-Mount
Mounting Suction cups, straps, multiple 1/4"-20 threads
Load Capacity
With Small Suction Cups 55 kg / 121.3 lb
With Large Suction Cup 100 kg / 220.5 lb
Physical
Materials Aluminum, stainless steel, rubber, ABS plastic
Dimensions 880 x 330 x 170 mm / 34.6 x 13 x 6.7"
Weight 6.5 kg / 14.3 lb

Description &In the Case

Description

The Tilta Hydra Alien is a modular car mount for a gimbal with a full camera rig, such as a DJI RS 3 Pro or RS 4 Pro. Unlike the small Hydra Alien Mini, which carries action and pocket cameras, it is built for full-size setups and offers plenty of mounting positions on the vehicle: on the hood, the roof, the doors, the rear or low along the side.

Modular build

Four dovetail plates (L1 to L4) link together in different ways, so you can rig high-angle shots from the roof as well as low shots close to the road. The rig attaches with one large and two small suction cups. The eight 220 g counterweights balance the rig depending on how you build it, and the ten suction cup cable clamps keep cables tidy along the car body.

Damping

A shock-absorbing arm with a hydraulic damping pole and a spring-loaded head soak up vibration and road shocks before they reach the gimbal. With the 90° connector you can mount the head at an angle.

Power while driving

The power baseplate for DJI RS Pro models feeds the gimbal while it is mounted. Two V-mount battery plates on a support bracket and two D-Tap cables, one straight and one angled, power the gimbal and camera from external batteries, so you don't have to stop to swap batteries.

Safe mounting and practical tips

Always secure the rig with the ratchet strap as well. After every drive, check every screw and make sure each suction cup still holds firm, since both can loosen over time. Drive slowly and carefully. Suction cups are not recommended on wrapped vehicles, because heat and direct sun can make them lose grip.

This kit is the standard version without Tilta's remote control kit, so plan ahead for how you'll trigger recording and monitor the picture (e.g., with a wireless video transmitter). Everything comes in a waterproof hard case.

In the Case
  • Dovetail plate L1 + 1x cable guide incl. dovetail sliding plate + thumb screw & long slotted screw
  • Dovetail plate L2 + 2x cable guide incl. 2x dovetail sliding plate + thumb screw & long slotted screw
  • Dovetail plate L3 + 2x cable guide
  • Dovetail plate L4 + 2x cable guide
  • Large suction cup
  • 2x small suction cup
  • 3x suction cup protector
  • Shock-absorbing arm with hydraulic damping pole + thumb screw
  • Shock-absorbing head + 4x long Phillips screws + 4x springs + 8x washers
  • Power supply baseplate for DJI RS Pro models
  • Plate + 2x 1/4" screw
  • Dual battery plate support bracket
  • 2x V-mount battery plate
  • 90° shock-absorbing head connector
  • Cross connector + thumb screw
  • Straight D-Tap power cable
  • Right-angle D-Tap power cable
  • L-bracket
  • 8x counterweight
  • 10x suction cup cable clamp
  • Ratchet strap
  • 7x red M25 screws; in a sealed bag: hex socket screw, 1/4" screw, 2x long hex screws, 6x small black hex screws, 2x Allen key, open-end wrench, manual, hard case

Gimbal, camera and V-mount batteries are not included, so don't forget to add them to your rental.

SHOPPING CART

close